HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] Unspecified Transmit Phase D error, including +FPHCTO timeout between data and +FET command (code 50)



Following error occurs, when I try to send a fax to some numbers. Ive found some people with the same problem in your mailing-list, but that didnt helped me to solve my problem

Im using version 4.1beta2-143. Is this problem solved in a later version?

 

Here are the logs:

 

Your facsimile job to 04717479 was not sent because:

Unspecified Transmit Phase D error, including +FPHCTO timeout between data and +FET command

 

The job will be retried at 18:09.

 

---- Transcript of session follows ----

 

Sep 17 18:00:30.07: [20991]: SESSION BEGIN 00000833 434717479

Sep 17 18:00:30.07: [20991]: SEND FAX: JOB 278 DEST 04717479 COMMID 00000833

Sep 17 18:00:30.07: [20991]: MODEM set DTR OFF

Sep 17 18:00:30.07: [20991]: DELAY 2600 ms

Sep 17 18:00:32.67: [20991]: MODEM set DTR ON

Sep 17 18:00:32.67: [20991]: MODEM set baud rate: 19200 baud, input flow NONE, output flow NONE

Sep 17 18:00:32.67: [20991]: MODEM flush i/o

Sep 17 18:00:32.67: [20991]: <-- [15:ATE0V1Q0S0=0H0\r]

Sep 17 18:00:32.82: [20991]: --> [2:OK]

Sep 17 18:00:32.82: [20991]: <-- [12:ATS8=2S7=60\r]

Sep 17 18:00:32.96: [20991]: --> [2:OK]

Sep 17 18:00:32.96: [20991]: <-- [14:AT+FCLASS=2.0\r]

Sep 17 18:00:33.10: [20991]: --> [2:OK]

Sep 17 18:00:33.10: [20991]: <-- [9:AT+FLO=0\r]

Sep 17 18:00:33.24: [20991]: --> [2:OK]

Sep 17 18:00:33.24: [20991]: <-- [9:AT+FPP=0\r]

Sep 17 18:00:33.38: [20991]: --> [2:OK]

Sep 17 18:00:33.38: [20991]: <-- [9:AT+FBO=0\r]

Sep 17 18:00:33.52: [20991]: --> [2:OK]

Sep 17 18:00:33.52: [20991]: <-- [10:AT+FCT=30\r]

Sep 17 18:00:33.66: [20991]: --> [2:OK]

Sep 17 18:00:33.66: [20991]: <-- [15:AT+FNR=1,1,1,1\r]

Sep 17 18:00:33.81: [20991]: --> [2:OK]

Sep 17 18:00:33.81: [20991]: <-- [9:AT+FIE=0\r]

Sep 17 18:00:33.95: [20991]: --> [2:OK]

Sep 17 18:00:33.95: [20991]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]

Sep 17 18:00:34.10: [20991]: --> [2:OK]

Sep 17 18:00:34.10: [20991]: <-- [5:ATM0\r]

Sep 17 18:00:34.24: [20991]: --> [2:OK]

Sep 17 18:00:34.24: [20991]: MODEM input buffering enabled

Sep 17 18:00:34.24: [20991]: <-- [14:AT+FCLASS=2.0\r]

Sep 17 18:00:34.48: [20991]: --> [2:OK]

Sep 17 18:00:34.48: [20991]: <-- [9:AT+FLO=0\r]

Sep 17 18:00:34.72: [20991]: --> [2:OK]

Sep 17 18:00:34.72: [20991]: <-- [9:AT+FPP=0\r]

Sep 17 18:00:34.96: [20991]: --> [2:OK]

Sep 17 18:00:34.96: [20991]: <-- [9:AT+FBO=0\r]

Sep 17 18:00:35.20: [20991]: --> [2:OK]

Sep 17 18:00:35.20: [20991]: <-- [10:AT+FCT=30\r]

Sep 17 18:00:35.44: [20991]: --> [2:OK]

Sep 17 18:00:35.44: [20991]: <-- [15:AT+FNR=1,1,1,1\r]

Sep 17 18:00:35.68: [20991]: --> [2:OK]

Sep 17 18:00:35.68: [20991]: <-- [9:AT+FIE=0\r]

Sep 17 18:00:35.92: [20991]: --> [2:OK]

Sep 17 18:00:35.92: [20991]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]

Sep 17 18:00:36.17: [20991]: --> [2:OK]

Sep 17 18:00:36.17: [20991]: <-- [27:AT+FLI="xxxxxxxxxxxxx"\r]

Sep 17 18:00:36.42: [20991]: --> [2:OK]

Sep 17 18:00:36.42: [20991]: DIAL 04717479

Sep 17 18:00:36.42: [20991]: <-- [13:ATDT04717479\r]

Sep 17 18:00:51.71: [20991]: --> [4:+FCO]

Sep 17 18:00:55.00: [20991]: --> [37:+FNF:_I_GOTTH-U-EBENBERG[______]

Sep 17 18:00:55.00: [20991]: REMOTE NSF "_I_GOTTH-U-EBENBERG[ ______"

Sep 17 18:00:55.00: [20991]: --> [27:+FCI:" +434717+479"]

Sep 17 18:00:55.00: [20991]: REMOTE CSI "+434717+479"

Sep 17 18:00:55.00: [20991]: --> [20:+FIS:1,3,0,2,1,0,0,5]

Sep 17 18:00:55.00: [20991]: --> [2:OK]

Sep 17 18:00:55.00: [20991]: REMOTE best rate 9600 bit/s

Sep 17 18:00:55.00: [20991]: REMOTE max page width 1728 pixels in 215 mm

Sep 17 18:00:55.00: [20991]: REMOTE max unlimited page length

Sep 17 18:00:55.00: [20991]: REMOTE best vres 7.7 line/mm

Sep 17 18:00:55.00: [20991]: REMOTE best format 2-D MR

Sep 17 18:00:55.00: [20991]: REMOTE best 20 ms/scanline

Sep 17 18:00:55.00: [20991]: USE 9600 bit/s

Sep 17 18:00:55.00: [20991]: USE 20 ms/scanline

Sep 17 18:00:55.00: [20991]: SEND file "docq/doc280.ps;01"

Sep 17 18:00:55.00: [20991]: USE page width 1728 pixels in 215 mm

Sep 17 18:00:55.00: [20991]: USE unlimited page length

Sep 17 18:00:55.00: [20991]: USE 7.7 line/mm

Sep 17 18:00:55.00: [20991]: USE 1-D MR

Sep 17 18:00:55.00: [20991]: <-- [23:AT+FIS=1,3,0,2,0,0,0,5\r]

Sep 17 18:00:55.25: [20991]: --> [2:OK]

Sep 17 18:00:55.25: [20991]: <-- [7:AT+FDT\r]

Sep 17 18:00:55.53: [20991]: --> [20:+FCS:1,3,0,2,0,0,0,5]

Sep 17 18:01:01.00: [20991]: --> [7:CONNECT]

Sep 17 18:01:01.00: [20991]: SEND begin page

Sep 17 18:01:10.98: [20991]: SENT 20631 bytes of data

Sep 17 18:01:10.98: [20991]: SEND 1D RTC

Sep 17 18:01:10.98: [20991]: SEND end page

Sep 17 18:01:10.98: [20991]: SEND send EOP (no more pages or documents)

Sep 17 18:04:10.98: [20991]: MODEM TIMEOUT: reading line from modem

Sep 17 18:04:10.98: [20991]: REMOTE HANGUP: Unspecified Transmit Phase D error, including +FPHCTO timeout between data and +FET command (code 50)

Sep 17 18:04:10.98: [20991]: <-- [7:AT+FKS\r]

Sep 17 18:04:40.98: [20991]: MODEM TIMEOUT: reading line from modem

Sep 17 18:04:40.98: [20991]: MODEM <Timeout>

Sep 17 18:04:40.98: [20991]: <-- [5:ATH0\r]

Sep 17 18:04:45.98: [20991]: MODEM TIMEOUT: reading line from modem

Sep 17 18:04:45.98: [20991]: MODEM <Timeout>

Sep 17 18:04:45.98: [20991]: MODEM set DTR OFF

Sep 17 18:04:45.98: [20991]: SESSION END

 

 

 




Project hosted by iFAX Solutions