HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] Modem does not answer fax calls (Re: Distinctive ring problems)

Hi all,

	I am trying to set up HylaFAX to receive fax using distinctive
rings. Based on the suggestion from George Bell I setup the modem
configuration file with information about distinctive rings. His
suggestions were very valuable. I can send a fax without any problems,
however the modem doesn't answer a fax call (any call for that
matter). I don't know what is missing from the config file?  George or
anyone else have any ideas?



-------------- config file --------------------

CountryCode:		1
AreaCode:		281
FAXNumber:		+1.281.856.0327
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		0xFFF
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"Home"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l %%n|%c|Page %%P of %%T"
MaxRecvPages:		50

ModemType:		Class2
ModemRate:		19200
ModemResetCmds: 	AT+VDR=1,10
ModemFlowControl:	rtscts
ModemNoFlowCmd:		AT&K0
ModemSoftFlowCmd:	AT&K4
ModemHardFlowCmd:	AT&K3
ModemRecvFillOrder:	MSB2LSB		# classic MultiTech
NoAnswerVoice:  	true
DistictiveRings:        V-20,F-8-4-8
DRingOn:                DRON=
DRingOff:               DROF=
#ModemSetupAACmd:	AT+FAA=1
ModemAnswerCmd:		AT+FCLASS=2;A

Class2APQueryCmd:	none		# not available
Class2BUGCmd:		none		# not available
Class2NFLOCmd:		AT+FLO=0
Class2SFLOCmd:		AT+FLO=1
Class2HFLOCmd:		AT+FLO=2

# The modem performs copy quality correction (in Class 2... gasp!)
# always, thus it's not a good idea to use host-based CQ.  The
# query response is incorrect, also.
Class2CQQueryCmd:	"!0-2"
Class2CQCmd:		AT+FCQ=1

# If your line supports Caller-ID, you may want to uncomment this...
#QualifyCID:		etc/cid		# you must create this file
#ModemResetCmds:	AT+VCID=1
#CIDNumber:		"NMBR="
#CIDName:		"NAME="

# Or with the MT5634ZBA-DID you'll probably need something like...
# ModemReadyCmds:	AT*DS1*DD0*DF1*DN4	# enable DTMF-DID, wink-start, 4 digits
# CIDNumber:		"DTMF"		# format of AT*DF1
# CIDNumberAnswerLength:	4	# four DTMF-DID digits then ATA

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Project hosted by iFAX Solutions